Note: Screens marked by '*' are not shown if local control is disabled (either programmed into non-volatile memory at factory or set by COMPEL command). Exception: "Audio Settings" screen is shown but only "Attenuation" may be changed by local user.

Click here for a non-colorized version of this chart.

MAIN LEVEL SECOND LEVEL THIRD LEVEL
Unit Label  (Home Screen) 
Prog: xxxxxx EbNo:y.y  (Program and Frequency alternate each 2-3 seconds.)
 
Audio Settings*
Press <SELECT>		 (Press <SELECT> then up/down to select presets.)
Preset Select:
Port 1:		  
  Preset Select:
Port 2:		  
  Detailed Settings
Press <SELECT>		 Port #: 1 Route: r
Srvc: sss Atten: aa
    Port #: 2 Route: r
Srvc: sss Atten: aa 
    Return
Press <SELECT>
  Return
Press <SELECT>		  
 
E-MAIL: NONE    
 
Hardware Setup
Press <SELECT>		 Current Settings*
Press <SELECT>		 RF In:- Freq: fffff.ff
Data Rate: rr.rrr
    FEC: Tag:tt
Prog: ppppp
    PIN #:
xxxxxxxx
    Save: <ENTER>
Cancel: <SELECT>
  Select Channel:* cc  
  Edit Channel:* cc  
  SNR Alrm Level: a.a
SNR Marg Offset: m.m		  
  Serial Ports
Press <SELECT>		 Serial 1: (Aux Data, Modem, Terminal, or Printer)
Serial 2: (Aux Data, Modem, Terminal, or Printer)
    Modem Password
              PASSWO
    Printer Settings (b=1200,2400,4800,9600,or19200)
Baud bbbbb Parity p (p = None, Even, Odd)
    Modem Settings (b=1200,2400,4800,9600,or19200)
Baud bbbbb Parity p (p = None)
    Aux. Data PID: pppp (b = Same as Ptr + 38400)
Baud bbbbb Parity p (p =None, Even, Odd)
    Return
Press <SELECT>
  LNB LO:fffff.ff
(<Select> for edit mode) 		 
  Unit Label:
20 Alphanumeric. Char's		  
  Control Expansion
Relays: Press Select		 Relay #01: Status
Press Select (to edit relay # and status)
    Return
Press <SELECT>
  To Reset Unit
Press <ENTER>		  
  Return
Press <SELECT>		  
 
Status Reports
Press <SELECT>		 Settings Status
Press <SELECT>		 Freq                    Mode
Data Rate   FEC Rate
    Tag:tt Mode
Prog:ppppp
    Return
Press <SELECT>
  Carrier Status
Press <SELECT>		 Mode: Status
Duration: hh:mm:ss
    Freq
Data Rate FEC Rate
    Program:ppppp
Tag site:
    EBNO 10 Sec Average
Margin: m.m Avg:AA.A
    Last Acq:hh:mm:ss
Hi/Lo EBNO:HH.H/LL.L
    First Acq:hh:mm:ss
Availability:xxx.xx%
    RF Level: Status
EB/No Level: Status
    Return
Press <SELECT>
  MPEG Status
Press <SELECT> 		 Aggregate MPEG:
Trans @ xx.xxx Mbps (Transport Data Rate)
    Program Presence
PPPPP ppppp 
    Video:
Normal
    < Audio Presence > (< > show more L or R)
AAA BBB CCC DDD EEE FFF
    Port1:SVC Mode
L:Status R:Status
    Port2:SVC Mode
L:Status R:Status
    Return
Press <SELECT>
  Settings Table
Press <SELECT>		 For each entry in the table: (First Screen)
Freq                   Mode
Data Rate  FEC Rate 
    For each entry in the table: (Second Screen)
Tag: x                 Mode
Prog: xxxxx
    Return
Press <SELECT>
  NC Status
Press <SELECT>		 S/N:xxxxxx Status
Compel: Status
    Local Ctrl:Status
Netwrk Mode:Status
    Last Hdr:hh:mm:ss
Last Adr:hh:mm:ss
    History:hh:mm:ss
Totl Processd: xxxxx
    Return
Press <SELECT>
  Parameter Status
Press <SELECT>		 LNB LO:fffff.ff
    SNR Alarm Level:xx.x
SNR Marg Offset:xx.x
    Fade: hh:mm:ss
Install: hh:mm:ss
    Search: hh:mm:ss
No Compel hh:mm:ss
    Cmpl Seek: hh:mm:ss
Hdr Srch: hh:mm:ss
    Aud Demux: Installed/Not Instl
Audio Ports: x
    Encryption: Installed/Not Instl
RF Switch: Installed/Not Instl
    Sync Data: Installed/Not Instl
    DVB-ASI: Installed/Not Instl
    Expansion Relay Card
Installed/Not Instl
    D1 Output: Installed/Not Instl
Transport Out: Status
    Return
Press <SELECT>
  Serial Port Status
Press <SELECT>		 E-mail:enabled/disabled
    Modem: Baud, Parity, Data Bits, Stop bits
Printer: Baud, Parity, Data Bits, Stop bits
    Return
Press <SELECT>
  (< > show more L or R)
< Expansion Relay #  >
Activated  (<None> or xx)		  
  Relay Status
1: Open/Cl 2: Open/Cl		  
  Return
Press <SELECT>		  
 
Version Info
Press <SELECT>		 Application
Version		  
  Boot Code
Version		  
  Audio Demux ( DSP )
Version		  
  Xilinx PLDs
Version		  
  Lattice PLD
Version		  
  Secure Micro
Version		  
  Video Decoder
Version		  
  Audio Decoder
Version		  
  Receiver Card
Version		  
  Conditional Access
Version		  
  Return
Press <SELECT>		  
 
Navigation Help
Press <SELECT>		 Press <- or -> to
Scroll		  
  Press <SELECT> to
start Edit mode		  
  Press <UP-DOWN) to
change value		  
  Press <ENTER> to
accept changes		  
  Press <SELECT> to
cancel changes		  
  Return
Press <SELECT>